|
Post by floh124 on May 22, 2020 10:08:16 GMT -5
Hello, I'm new to FSFO but the different videos existing and some reviews showed me, that I "NEED" it... Unfortunaltly it does not work on my installation. I did install it as Administrator and run it the same way. It connects (shown in green) and when I open the main exit it shows me that the FO will take seat but after this 30 sec, nothing happens. Equal which airplane (PMDG 737NGXu, 777 or QW787). Also I can't command anything...
Maybe someone had the same experience.
Best regards Florian
|
|
|
Post by Matthew King on May 22, 2020 13:28:47 GMT -5
Good afternoon, Florian.
What happens when you click the Pre Flow button? The Copilot won't automatically start his flow unless you enable "auto." From the main form, is AUT enabled (i.e. green)?
Could you let me know what sim you're using? Don't worry, we'll get you up and flying.
AUT Turns automatic flows on/off. When activated (green), the copilot will initiate his flows based on the following parameters: · Pre Flight Flow: Initiated when FSFO is connected and the main door is open · Before Start Flow: Initiated when all doors are closed · After start flow: Initiated when engines are turning and stable; it may take up to 2 mins for the engines to stabilize. · After Landing Flow: Initiated when
|
|
|
Post by floh124 on May 22, 2020 15:24:02 GMT -5
Hello Matthew, I'm using P3D V4 Hotfix 2 (not 3 because of TACPACK). I also own FSUIPC (registered/V6.0.0.8). Tell me if you need more details.
And AUT is on so far. But it doesn't matter if I select it manually (by pushing the button on main form) or let the "AUT"-Function do it. The "Pre Flight Flow" Button on the Main Form is shown in yellow but nothing happens at all.
If I push the button manually it shows this aborted advise but doesn't do anything after selecting it manually. I also tried every other button without effect.
Best Regards Florian
|
|
|
Post by Matthew King on May 22, 2020 19:12:18 GMT -5
Perfect! How are you starting your aircraft? Cold and Dark? If the button is yellow, the copilot is executing the flow; however, the flows are silent...he doesn't make any remarks. If the switch is set correctly, he simply moves to the next item. If you're starting in a cold and dark state, and he doesn't energize the aircraft, we have an issue.
For your PMDG aircraft, have you configured the .ini file to allow broadcasting?
|
|
|
Post by floh124 on May 23, 2020 4:15:47 GMT -5
Yes, these parameter in the PMDG .ini file is already set. And the same behaviour is also on the QW 787. Also I tried several Cockpit states. Also cold and dark and the FSFO doesn't start up anything.
|
|
|
Post by Matthew King on May 23, 2020 12:29:54 GMT -5
Thanks Flo! Ok, FSUIPC 6 is new and hasn't really been tested; perhaps there's a problem there. I've updated FSFO's FSUIPCclient.dll and hope that solves your problem. Tomorrow, would you mind downloading FSFO Pro V1.13 from simmarket and installing? Please completely uninstall V1.12 and disable your anti-virus service before installing V1.13. I truly appreciate your help, sir! It's been a while since we've had any issues with FSFO to solve.
|
|
|
Post by floh124 on May 24, 2020 15:10:16 GMT -5
Hello Matthew, will check it tomorrow. Sorry, was quite busy on the weekend...
Best regards
|
|
|
Post by floh124 on Jun 6, 2020 5:14:15 GMT -5
Hello Matthew, please excuse my long delay but I did a complete new installation of my OS and also P3D. So with this I also changed now to the latest HF of P3D, but unfortunately I have to report, FSFO has exactly the same behavior like before. For sure, I also now installed 1.13. But again same behavior: for example: If I open the door on a cold and dark 737 (or same on the 787) and wait for the 30 seconds, FSFO is not reacting anymore... Nothing happens. Best regards Florian
|
|
|
Post by Matthew King on Jun 6, 2020 11:05:56 GMT -5
Hello Matthew, please excuse my long delay but I did a complete new installation of my OS and also P3D. So with this I also changed now to the latest HF of P3D, but unfortunately I have to report, FSFO has exactly the same behavior like before. For sure, I also now installed 1.13. But again same behavior: for example: If I open the door on a cold and dark 737 (or same on the 787) and wait for the 30 seconds, FSFO is not reacting anymore... Nothing happens. Best regards Florian Welcome back, sir. Ok, are you opening the door via ctrl+e? FSFO may not recognize the door being opened if it's done via CDU. Would you being willing to do a team sharing session so I can see what's going on?
|
|
|
Post by floh124 on Jun 9, 2020 14:38:25 GMT -5
Hello Matthew, for sure, we can do a team sharing session... Via Teamviewer? In which time zone are you. I'm more or less flexible these days.
Best regards Florian
|
|
|
Post by Matthew King on Jun 9, 2020 17:54:21 GMT -5
Hello Matthew, for sure, we can do a team sharing session... Via Teamviewer? In which time zone are you. I'm more or less flexible these days. Best regards Florian TeamViewer is perfect, sir. I'm on PST; anytime this weekend should work...just let me know and thanks for the assist.
|
|